Updates and Changes

Raising CW Plate- and Screen-Voltages

Collins' reduction in High Voltage and Screen Voltage when using CW mode held back the 4CX1500B gain, and total-power. I was almost at the point of using the SSB setting for CW (as many do), when Chet VE3CFK pointed out...

That feeding both the primary wires from the front-panel-switch to the SSB connections on the transformer would give me a constant 3kV plate-voltage, and the elevated screen-voltage, no matter the mode. In fact, doing this means the only difference between SSB and CW is the negative grid-bias, and the resulting Class of operation.

The realization of Chet's suggestion: simply moving the CW-primary-power wire from Term #1 to Term #2, and similarly moving Term #6 to Term #5:

Now I have good gain and total power! Thanks, Chet! Here's a view of comfortable operating conditions now, for CW:

Raising the Screen supply meant my C204 Voltage rating was marginal... Here, I did a mod to a mod ;-) 500V / 105C rating are improvments over the 450V/85C new capacitor I recently installed.

Installing the 4CX1500B

Ready...

AIM...

Date-code of (mid-December) 1984. 12 hours of filament-only to getter the tube, after such long storage.

FIRE!

This photo shows 1kW into my dummy-load, making it sweat a bit :-) But my calculation of the DC input power, now compared with the RF output-power, leads me to question my Plate Current meter accuracy. Another detour...

Cooling

Collins' original blower is very quiet. Nicely quiet. This is pretty much a result of laminar-airflow over the tube-fins, with a (nominal) 1800rpm motor.

The fin-design of the 4CX1500B includes offset-punched sections of each fin, intentionally to cause turbulence and remove more heat. I made that much worse :-) by swapping blower-motors - I swapped in the popular 3600rpm Dayton 4M093E. Some correspondance and digging through Collins' maillist archives led me to choose a 50-ohm series-resistor, primarily to keep the motor from overheat-tripping (this motor will overheat without some sort of slow-down, because it's intended to have airflow over the motor, and in this 30S-1 application it does not have cooling airflow over it).

The line-up of prime-suspects for the blower-motor change :-)

<<photo of installed parts to come>>

My cut-off tool got a workout: the Dayton motor has front and rear mounting-bolts; I didn't like the knuckle-slicing appearance of the rear ones so I cut them off and added some protective heatshrink. I trimmed the front bolts down, to allow more lattitude in adjusting the squirrel-cage. And my 1/4" nut-driver was too long to fit into the blower compartment, so I cut that too :-)

For this 50-ohm resistor, I measured:

• 0.980 amps without resistor nor any nozzle-restriction (121VAC)
• 0.76 amps with resistor in steady-state (10-12s after start)
• 93VAC across motor, with resistor, in steady-state

Pretty much, this shifts the original motor-dissipation from 120W without a resistor, down to 70W in the motor and 32W in the resistor. Subjectively, the airflow seems the same, but the motor-temperature will be 'way down.

Test driving the new blower made my beach-towel wave in the wind, from 3 feet away :-) Too much is just about right :-)

<<graph of predicted blower performance>>

Predicted performance was reassuring, but I felt the need to measure and determine actual performance. Tachometer: 3214rpm Temperature: Manometer Pressure:

And Then...

I bought a Variable-Voltage / Variable Frequency controller! This V/F motor drive is ~perfect~ for the Dayton shaded-pole motor... My Plan: slow the motor when possible and enjoy quiet-ness, then speed it up when cooling is required. This V/F drive can be controlled with a 0-5V signal, so ... :-)

Thermal Overload Switch K102

My thermal sensor kicked my amp offline a couple of times, at only modest power-levels. Perhaps decades of time have taken their toll on the sensor; perhaps tube-changes have un-calibrated it; certainly my blower-motor-change will have altered it's response. The purpose of the thermal sensor: to open the HV-enable 12V circuit and K203 (primary AC power) if the tube gets too hot. The tube can get too hot with either excess dissipation, or lack of cooling-airflow.

I changed this protection to accurately focus on protecting the tube against overtemperature and also against loss of cooling airflow.

How and Why I Changed It

• Thermal and Pressure switches to replace Collins Overtemp K102
• 

  Rear View of the RF Compartment, Showing New Thermal-Safety

• 

  Top View of the RF Compartment, Again Showing Thermal-Safety

• 

  Air-Pressure sensing tube simply stuck up between blower nozzle, and flexible coupling-boot

Dial Lights "ON" when Amp is Ready

I re-wired the dial-lights so they will illuminate only after the warm-up delay has passed and K202 closes. Not only does this indicate visually that the amp has completed the 3min warm-up and ready to hit the "ON" push-button, but it also confirms 12V is available to energize K203 - maybe this will help troubleshooting one day. (Technical note: this "delay completed" lighting moves the dial bulbs from 12VAC to ~15VDC operation).

Final touch for the dial-light mod: hand-lacing!