160m Mods: Difference between revisions

From Collins 30S-1 HF Amplifier
Jump to navigation Jump to search
No edit summary
No edit summary
Line 21: Line 21:


[[File:160m_input_wafer_mods2.jpg|500px|thumb|center|Fig.4 160m tabs added to input-switch-wafer]]
[[File:160m_input_wafer_mods2.jpg|500px|thumb|center|Fig.4 160m tabs added to input-switch-wafer]]
[[File:160m_vna_s11.jpg|500px|thumb|center|Fig.9 VNA showing S11 for 160m input-circuit Zload=50 Ohms]]
[[File:160m_vna_s11.jpg|500px|thumb|center|Fig.5 VNA showing S11 for 160m input-circuit Zload=50 Ohms]]


[[File:160m_ouptput_PA.jpg|500px|thumb|center|Fig.5 Clearing a path to the rear PA band wafer for removal]]
[[File:160m_ouptput_PA.jpg|500px|thumb|center|Fig.6 Clearing a path to the rear PA band wafer for removal]]


<gallery class="center" caption="PA-Wafer. Adding 80m and 160m tabs" widths="400px" heights="400px" >
<gallery class="center" caption="PA-Wafer. Adding 80m and 160m tabs" widths="400px" heights="400px" >
Line 30: Line 30:
</gallery>
</gallery>


[[File:Input_switch_wafer.jpg|500px|thumb|center|Fig.6 160m added ordinary wafer for 160m PA vacuum relay switching]]
[[File:Input_switch_wafer.jpg|500px|thumb|center|Fig.7 160m added ordinary wafer for 160m PA vacuum relay switching]]


[[File:Switch_wafer_arrow.jpg|500px|thumb|center|Fig.7 160m band switch with stop drilled out]]
[[File:Switch_wafer_arrow.jpg|500px|thumb|center|Fig.8 160m band switch with stop drilled out]]


[[File:160m_vacuum_relay.jpg|500px|thumb|center|Fig.8 160m 160m PA vacuum relay]]
[[File:160m_vacuum_relay.jpg|500px|thumb|center|Fig.9 160m 160m PA vacuum relay]]

Revision as of 03:38, 27 May 2020

160m Mods. The 160m mods involve working on: 1. the input PI section, 2. the PA output PI section. 3. changing one of the bandswitch stops.


It's a tight fit inside the input circuit compartment. Facing the front, the 160m variable coil is mounted on the left side next to the 80m coil. The fixed coil and SM caps are tucked inside the semi closed aluminum box.

NB. It appears there are two different 30S1 input circuits depending on the age of the 30S-1 amp. The 160m mod is practical only for input circuits using simple wafers with contacts on one side only. If there is a grounding ring in addition to a selector ring then things get rather complicated. This mod does not deal with the double sided grounding wafers for obvious complex fabrication reasons. The wafers used in the 30S-1 are 45 degree type, next to impossible to find. The bakelite material is old and very easy to fracture. Utmost care is necessary to prevent breakage. The alternative is to make new blanks with FR40 board material a time consuming proposition.

Collins uses 1KV ceramic disk capacitors for the other bands, ideally the 160m capacitors should be 1 KV SM but space is tight. The 500V SMs i showed no leakage up to 1.5KV, and should should be ok up to 100W 3-1 SWR. Alpha 77Sx uses compression silver micas, which have higher Q than ceramics.

Fig.1 Schematic showing 160m additions to the PA
Fig.2 160m input-Pi circuit and L, C elements
Fig.3 160m input-switch-wafer modifications
Fig.4 160m tabs added to input-switch-wafer
Fig.5 VNA showing S11 for 160m input-circuit Zload=50 Ohms
Fig.6 Clearing a path to the rear PA band wafer for removal
Fig.7 160m added ordinary wafer for 160m PA vacuum relay switching
Fig.8 160m band switch with stop drilled out
Fig.9 160m 160m PA vacuum relay